DEGREES AND CERTIFICATES
Associate in Science Degree
To receive an Associate in Science degree from El Camino College, a student must complete at least 60 units in degree applicable college courses which must include general education requirements and course work in an approved transfer major or associate degree program. Course work toward the degree must be completed with a cumulative grade point average (GPA) of 2.00 or higher. A minimum of 12 of the required 60 degree applicable units must be successfully completed at El Camino College. A notation of “Graduation with Honors” is earned with a cumulative GPA of 3.5 or higher. Students must file an intent to graduate in the evaluations area located in the Admissions Office by the deadline date published in the schedule of classes.
At least 50% of the major requirements for the Associate in Science Degree must be completed at El Camino College.
Major Requirements:
Complete the following:
| Computer Aided Design/Drafting 5 |
Introduction to Mechanical Drafting |
(3 units)
|
Computer Aided Design/Drafting 10abcd*
|
Introduction to Mechanical Computer
Aided Design/Drafting |
(3 units)
|
| Computer Aided Design/Drafting 27abcd* |
Creating Assemblies with Autodesk Software |
(2 units)
|
Computer Aided Design/Drafting 28abcd*
|
Design, Analysis, and Management of Assemblies with Autodesk Software |
(2 units)
|
| Computer Aided Design/Drafting 31abcd* |
Orientation to CATIA |
(2 units)
|
| Computer Aided Design/Drafting 32abcd* |
Product Modeling with CATIA |
(2 units)
|
| Computer Aided Design/Drafting 34abcd* |
Drafting with CATIA |
(2 units)
|
| Computer Aided Design/Drafting 45 |
Geometrical Dimensioning and Tolerancing |
(2 units)
|
Computer Aided Design/Drafting 47
|
Two Dimensional Mechanical Computer Aided Design/Drafting |
(3 units)
|
Computer Aided Design/Drafting 49
|
Advanced Two Dimensional Mechanical Computer Aided Design/Drafting |
(3 units)
|
| Technical Mathematics 1 |
Technical Mathematics for Vocational Students |
(3 units)
|
*one semester of
2 units from the following:
| Computer Aided Design/Drafting 26abcd* |
Creating Solid Models with Autodesk Software |
(2 units)
|
| Computer Aided Design/Drafting 33abcd* |
Analysis and Simulations with CATIA |
(2 units)
|
|
Note:
CADD 33 will only be offered in fall 2009, CADD 33 will not be offered in spring 2010. Please check the college catalog for other course options.
|
| Computer Aided Design/Drafting 37abcd* |
Advanced CATIA Functions |
(2 units)
|
*one semester of
1 course from the following:
| Electronics 11 |
Introduction to Electronics |
(3 units)
|
| Electronics and Computer Hardware Technology 22 |
Basic Electronic Fabrication
|
(3 units)
|
| Machine Tool Technology 16ab |
General Metals |
(3 units)
|
| Machine Tool Technology 46 |
Basic Machine Tool Operations |
(3 units)
|
| Machine Tool Technology 101abcd |
Introduction to Conventional and CNC Machining |
(4 units)
|
| Welding 15ab* |
Basic Welding for Allied Fields |
(3 units)
|
| Art 141abcd* |
Digital Art |
(3 units)
|
| Art 144abcd* |
There-Dimensional Computer Animation |
(3 units)
|
| Computer Information Systems 13 |
Introduction to Computers |
(3 units)
|
*one semester of
Total Units: 33-34
Certificates of Achievement
A Certificate of Achievement is awarded to students who complete the prescribed program with a 2.0 grade point average.
A Certificate of Achievement with Honors is awarded to students who complete the prescribed program with a 3.0 grade point average.
A Certificate of Achievement with High Honors is awarded to students who complete the prescribed program with a 3.5 grade point average or above.
A Certificate of Achievement will be granted upon completion of the courses listed below. At least 50% of the courses required for the Certificate of Achievement must be completed at El Camino College.
Complete the following:
| Computer Aided Design/Drafting 5 |
Introduction to Mechanical Drafting |
(3 units)
|
Computer Aided Design/Drafting 10abcd*
|
Introduction to Mechanical Computer
Aided Design/Drafting |
(3 units)
|
| Computer Aided Design/Drafting 27abcd* |
Creating Assemblies with Autodesk Software |
(2 units)
|
Computer Aided Design/Drafting 28abcd*
|
Design, Analysis, and Management of Assemblies with Autodesk Software |
(2 units)
|
| Computer Aided Design/Drafting 31abcd* |
Orientation to CATIA |
(2 units)
|
| Computer Aided Design/Drafting 32abcd* |
Product Modeling with CATIA |
(2 units)
|
| Computer Aided Design/Drafting 34abcd* |
Drafting with CATIA |
(2 units)
|
| Computer Aided Design/Drafting 45 |
Geometrical Dimensioning and Tolerancing |
(2 units)
|
Computer Aided Design/Drafting 47
|
Two Dimensional Mechanical Computer Aided Design/Drafting |
(3 units)
|
Computer Aided Design/Drafting 49
|
Advanced Two Dimensional Mechanical Computer Aided Design/Drafting |
(3 units)
|
| Technical Mathematics 1 |
Technical Mathematics for Vocational Students |
(3 units)
|
*one semester of
2 units from the following:
| Computer Aided Design/Drafting 26abcd* |
Creating Solid Models with Autodesk Software |
(2 units)
|
| Computer Aided Design/Drafting 33abcd* |
Analysis and Simulations with CATIA |
(2 units)
|
Note:
CADD 33 will only be offered in fall 2009, CADD 33 will not be offered in spring 2010. Please check the college catalog for other course options. |
| Computer Aided Design/Drafting 37abcd* |
Advanced CATIA Functions |
(2 units)
|
*one semester of
1 course from the following:
| Electronics 21 |
|
|
| Electronics and Computer Hardware Technology 22 |
Basic Electronic Fabrication
|
(3 units)
|
| Machine Tool Technology 16ab |
General Metals |
(3 units)
|
| Machine Tool Technology 46 |
Basic Machine Tool Operations |
(3 units)
|
| Machine Tool Technology 101abcd |
Introduction to Conventional and CNC Machining |
(4 units)
|
| Welding 15ab* |
Basic Welding for Allied Fields |
(3 units)
|
| Art 141abcd* |
Digital Art |
(3 units)
|
| Art 144abcd* |
There-Dimensional Computer Animation |
(3 units)
|
| Computer Information Systems 13 |
Introduction to Computers |
(3 units)
|
*one semester of
Total Units: 33-34
|
Engineering and